Brug læseren nedenfor til at læse Sceptre E246BV-FHD TV brugsanvisningen. Du kan bladre gennem brugsanvisningen direkte på siden og bruge vores læsers funktioner til at finde alle vigtige oplysninger om installation, betjening og vedligeholdelse af denne Sceptre TV.
Brugsanvisning
Fuld skærmFejlfinding
Praktiske tips til at løse de mest almindelige problemer med Sceptre E246BV-FHD.
Årsag: Power not connected, video cable not connected properly, or incorrect input signal source selected
Connect power cord correctly. Turn on power. Connect video cable correctly. Select the input signal source with proper cable connection using the source button.
Årsag: Cable colors not matched to correct ports
Match the colors on the cables to the ports on the back of the television. For example, red cable to red colored port.
Årsag: Contrast, brightness, or lamp settings not adjusted properly
Adjust your contrast, brightness and lamp settings from the OSD Menu. For adjustment controls, refer to page 27.
Årsag: Video cable not connected or tuner signal too weak
Make sure you have connected both your video and audio cables. The TV's tuner signal must not be lower than 65%.
Årsag: Audio cable not connected, volume too low, or tuner signal too weak
Make sure the audio cable is connected. Readjust your volume via the remote control. The TV's tuner signal must not be lower than 65%.
Årsag: Battery depletion or remote sensor not aligned with TV sensor
Turn off the TV, unplug it from the socket. Remove the batteries from the remote for 30 minutes. Press the remote buttons and the power button randomly for a good 2 seconds, and then reinstall the batteries. Ensure line of sight from the remote control's front sensor to the TV's remote sensor.
Årsag: Tuner signal too weak or antenna direction incorrect
The TV's tuner signal must not be lower than 65%. Change the direction of your antenna and rescan your channels. If you have cable, call your cable company and ask about signal strength of your local cable.
Årsag: Picture settings not adjusted properly, saturation or RGB turned down
Please adjust your picture setup and make sure the saturation and the RGB are not turned all the way down. For adjustment controls refer to page 27. The TV's tuner signal must not be lower than 65%. Check your signal.
Årsag: Tuner signal too weak or antenna direction incorrect
The TV's tuner signal must not be lower than 65%. Change the direction of your antenna and rescan your channels. If you have cable, call your cable company and ask about signal strength of your local cable.
Årsag: Some channels locked in OSD settings
Check your auto lock function's settings inside the OSD. You may have locked up some channels but forgot about them. Refer to page 34 for more instructions.
Årsag: TV requires more startup time than standard televisions
This is normal for this High Definition liquid crystal display panel TV. It requires a few more seconds than normal TVs to power up and show the picture.
Årsag: 3.5 mm mini-jack cable not connected from PC to TV
Make sure you have a 3.5 mm mini-jack cable connected from your PC's sound output to the TV's VGA STEREO INPUT.
Årsag: HDCP video device not responding properly
Reboot your HDCP video device by turning them off and unplugging the power cord. Wait up to 8 minutes to plug the power back in to see if it works or not.
Årsag: Audio cable not connected or incorrect cable type used
Make sure you have a 3.5 mm mini-jack cable connected from your HDCP video device's sound output to the TV's VGA STEREO INPUT. If your HDCP video device uses RCA AUDIO jacks, you'll need to obtain a RCA audio converted into 3.5 mm mini-jack cable.
Årsag: TV not recognized as plug and play monitor or outdated video card drivers
Make sure the TV is recognized as plug and play monitor. Try updating your video card's drivers as well. If that does not help, most likely you'll need to upgrade your video card to a newer one.
Årsag: Interference from large electrical appliances, cars, motorcycles, or fluorescent lights
This might be from interference from large electrical appliances, cars, motorcycles, or fluorescent lights. If the TV is close to the wall, try moving the TV to another room in your house to see if the problem still occurs.
Årsag: Aspect ratio not set correctly for the input source
If you're using HDMI or a TV digital channel make sure you use the ASPECT button to switch to 16:9 format. If you are using VGA, use the AUTO ADJUST function to adjust to the screen. For regular analog TV, AV, or component in 480i resolution, use the ASPECT button to switch to 16:9 to fill up the screen.
Årsag: Low quality source material or poor broadcast resolution
For best image quality, view HD widescreen programs where possible. If HD content is not available view Standard Definition from a digital source. Standard, analog TV will always be noticeably inferior to HD because your TV has video that is many times better than old TV's.
Årsag: Pixel defect within industry specifications
Your TV is manufactured using an extremely high level of precision technology, however, sometimes some pixels of your TV may not display. Pixel defects within industry specifications are inherent to this type of product and do not constitute a defective product.
Årsag: TV syncs time automatically from local TV channel
Your TV syncs time automatically according to your local TV channel. This function only works while the TV's tuner is connected to an ANTENNA.
Årsag: Closed captioning enabled with TEXT1-TEXT4 mode
You have turned on closed captioning and are using TEXT1 – TEXT4. Change the setting to CC1 or turn off closed captioning and the box will disappear. Refer to page 40 for more information.
Årsag: Different channels and inputs have different signal volume levels
Different channels and inputs will sometimes have this effect because the channel signal's own volume is already loud. There is no way to remove this completely. The TV has an AUTO VOLUME LEVEL function that can combat this type of effect. Please make sure that function is turned on.
Årsag: Resolution up-conversion from lower broadcast resolution
When your TV's resolution is higher than the digital channel's broadcast resolution, the signal is up-converted to match your TV's resolution. Up-converting can cause this type of effect.
Årsag: Power saving mode activated
The TV features a power saving mode which will automatically turn off the TV, if there's no signal provided for more than 5 minutes.
Ofte Stillede Spørgsmål
De mest almindelige spørgsmål om Sceptre E246BV-FHD.
Hjælp
Har du spørgsmål om TV E246BV-FHD fra Sceptre? Stil dem direkte til vores ekspert! Du får information, praktiske tips og skræddersyede løsninger på få sekunder.
Relaterede brugsanvisninger
Nedenfor finder du brugsanvisninger til TV der ligner E246BV-FHD. Prøv også at se alle Sceptre TV brugsanvisninger
Diskussion
Efterlad en kommentar eller stil et spørgsmål
Deltag i diskussionen
Stil et spørgsmål om brugsanvisningen eller tilføj et nyttigt svar til andre brugere.